氣閥門英文

1. 氣動閥門的英文翻譯

Pneumatic valve

2. 誰能告訴我有關各種閥門的英語翻譯！！！

你要的基本上都有了，各種閥的名稱、部件，相關用語。
如果你要各種閥門的解釋，到這里
http://valve-2000.nease.net/shuyu.htm

CQ螺紋球閥 CQ Thread Ball Valves
L形三通式 L-pattern three way
T形三通式 T-pattern three way
安全閥 Safety valve
暗桿閘閥 Inside screw nonrising stem type gate valve
百葉窗; 閘板 shutter
百葉窗式擋板 louver damper
擺閥式活塞泵 swing gate piston pump
保溫式 Steam jacket type
報警閥 alarm valve
報警閥; 信號閥; 脈沖閥 sentinel valve
背壓調節閥 back pressure regulating valve
背壓率 Rate of back pressure
本體閥桿密封 body stem seal
波紋管閥 Bellows valves
波紋管密封閥 bellow sealed valve
波紋管密封式 Bellows seal type
波紋管平衡式安全閥 Bellows seal balance safety valve
波紋管式減壓閥 Bellows recing valve
波紋管式減壓閥 Bellows weal recing valve
薄膜 thin film
薄膜; 隔膜 diaphragm
薄膜式減壓閥 Diaphragm recing valve
薄型閘閥 Thin Gate Valves
不封閉式 Unseal type
槽車球閥 Tank Lorry Ball Valves
顫振 Flutter
常閉式 Normally closed type
常開式 Normally open type
超低溫閥門 Cryogenic valve
超高壓閥門 Super high pressure valve
超過壓力 Overpressure of a safety valve
襯膠隔膜閥 rubber lined diaphragm
襯膠截止閥 rubber lined globe valve
垂直板式蝶閥 Vertical disc type butterfly valve
磁耦合截止閥 Magnetic Co-operate Globe Valves
帶補充載荷的安全閥 Supplementary loaded safety valve
帶輔助裝置的安全閥 Assisted safety valve
單閥碟雙面平行密封閘閥 parallel single disk gate valve
單口排氣閥 Single Opening Exhaust Valves
單向閥 Non-return Valve
單閘板 Single gate disc
單閘板平板閘閥 Single Disc Flat Gate Valves
彈簧薄膜式減壓閥 Spring diaphragm recing valve
彈簧式安全閥 Direct spring loaded safety valve
彈簧座 Spring plate
彈性閘板 Flexible gate disc
當量計算排量 Equivalent calculated capacity
擋板 damper
導閥 Pilot valve
導向套 Valve guide disc guide
低溫閥門 Sub-zero valve
低壓閥門 Low pressure valve
底閥 bottom valve
底閥 Foot valve
電磁動裝置 Eletro magnetic actuator
電磁閥 magnetic valve
電磁閥 solenoid valve
電磁－液動裝置 Eletro magnetichydraulic actuator
電動閥 mortor operated valve
電動閥 motorized valve
電動截止閥 Electric Actuated Stop Valves
電動平行式雙閘板閘板 Electric Double Disk Parallel Gate Valves
電動楔式閘閥 Electric Actuated Wedge Gate Valves
電動裝置 Electric actuator
電－液動裝置 Eletro hydraulic actuator
電液伺服閥 electro-hydraulic servovalve
調節彈簧 Regulation spring
調節閥 adjusting valve
調節閥 control valve
調節閥 regulating valve
調節螺套 Adjusting bolt Adjusting screw
調節圈 Adjusting ring
蝶板 Disc
蝶閥；瓣閥 butterfly valve
蝶閥；瓣閥；拍門；鉸鏈閥 flap valve
蝶式緩沖止回閥 Butterfly Type Non-slam Check
蝶式止回閥 Butterfly swing check valve
定比減壓閥 Proprutioning pressure recing valve
定差減壓閥 Fixed differential recing valve
定值減壓閥 Fixed pressure recing valve
動態特性 Dynamic characteristics
對焊連接閥 Buttwelding valves
對夾蝶板閥 Wafer plate valves
對夾式襯膠蝶閥 Wafer Type Butterfly Valves with Rubber Itning
對夾式閥門 Clamp valves
對夾式止回閥 Wafer Check Valves
額定排量 Certified capacity
額定排量系數 Derated coefficient of discharge
二通閥 Two-way valves
閥 valve
閥板 valve deck plate
閥板 valve plate
閥板式活塞泵 valve deck plate type piston pump
閥板式活塞泵 valve plate type piston pump
閥瓣 Disc
閥操縱桿 valve operating rod
閥痤槽 valve seat recess
閥擋 valve grid
閥擋 valve positioner
閥擋 valve stop
閥導桿 valve tail rod
閥導向器 valve guide
閥蓋 bonnet
閥蓋襯套 bonnet bush
閥蓋墊片 bonnet gasket
閥桿 stem
閥桿 valve rod
閥桿 valve spindle
閥桿端部尺寸 Dimmension of valve stem end
閥桿環 stem ring
閥桿螺母 Yoke bushing Yoke nut
閥桿填料 stem packing
閥桿頭部尺寸 Dimension of valve stem head
閥簧 valve spring
閥簧壓板 valve spring plate
閥控水錘泵 valve-controlled hydraulic ram
閥框架 valve yoke
閥門 Valve
閥門傳動裝置 valve bandle set
閥門和管件 Valves and Fittings
閥門盤根 valve packing
閥門手柄 valve handle
閥盤 disc
閥盤 valve disc
閥片 Disc
閥球 valve ball
閥驅動臂 valve driving arm
閥驅動臂 valve motion arm
閥式活塞 valve type piston
閥式活塞 valve type bucket
閥室式活塞泵 valve box type piston pump
閥室式活塞泵（美） valve pot type piston pump
閥抬起裝置 valve lifting device
閥體 body
閥體 valve body
閥箱 valve box
閥箱 valve cage
閥箱 valve chest
閥箱；閥限位器 valve guard
閥箱蓋 cover for valve box
閥箱蓋 valve box cover
閥箱式活塞泵（美） turret type piston pump
閥形活塞泵 valve type piston pump
閥座 Seat ring
閥座 valve carrier
閥座 valve seat(body seat)
閥座；閥盤 valve seat
閥座環 seat ring
閥座密封嵌條 sealing strip for valve seat
法蘭 flange
法蘭堵頭 blind flange
法蘭端 flange end
法蘭接頭 flange joint
法蘭連接緊固件（雙頭螺栓和螺帽） flange bolting
法蘭密封面，法蘭面 flange facing
法蘭面加工 flange facing finish
法蘭球閥 Flange Ball Valves
翻板閥 Flap
反沖盤 Disc holder
反向作用式減壓閥 Reverse acting recing valve
反向作用式減壓閥 Reverse acting recing valve
放空閥 emptying valve
放氣閥 air vent valve;vent valve
放氣閥；排氣閥 air evacuation valve
放泄閥 escape valve
分置閥室式活塞泵 separate valve box type piston pump
分置閥室式活塞泵（美） side pot type piston pump
封閉式 Seal type
浮動式球閥 Float ball valve
浮球 Ball float
浮球閥 Float Valve
浮球式疏水閥 Ball float steam trap
浮球式疏水閥 Free Float Type Steam Trap
浮桶 Bucket float
浮桶式疏水閥 Open bucket steam trap
輔助（副）閥 Auxiliary valves
負荷率 Rate of load condensate
附加背壓力 Superimposed back pressure
復位彈簧 Returnning spring
杠桿式 Lever type
杠桿式安全閥 Lever and weight loaded safety valve
杠桿式減壓閥 Lever recing valve
高溫閥門 High temperature valve
高壓閥門 High pressure valve
格蘭密封 gland
隔離閥 isolating valve
隔膜 Diaphragm
隔膜閥 diaphragm valve
隔膜式控制閥 diaphragm operated comtrol valve
工作背壓 Operating back pressure
工作溫度 Operating temperature
工作溫度 Working temperature
工作壓差 Operting differential pressure
工作壓力 Operating pressure
工作壓力 Working pressure
公稱通徑 Nominal diameter
公稱壓力 Nominal pressure
固定式球閥 Fixed ball valve
關閉壓力 Lockup pressure
關閥過冷度 Subcooled temperature of close valve
關閥溫度 Closing valve temperature
管道安全閥 Piping Safety Valves
過冷度 Subcoold temperature
過流閥(或節流閥) Restrictor Valves
喉徑 Throat diameter
滑閥 slide valve
滑閥式回轉活塞泵 rotary piston pump with slide gate
滑閥型轉子泵 eccentric rotary pump with sliding sleeve
環形閥 annular valve
環形閥 double beat valve
換向閥 selector valve
換向閥 shuttle valve
回轉滑閥活塞泵 piston pump with rotary gate
回座壓力 Re-seating pressure of a safety valve
活塞昵減壓閥 Piston recing valve
活塞式閥 piston valve
活塞式閥；柱塞式閥 plunger valve
活塞式減壓閥 Piston recing valve
減速閥 Deceleration valves
減壓比 Pressure recing ratio
減壓閥 pressure recing valve
漿液閥 Parallel Slide Valves
角閥 Angle Valve
角閥 isolation valve angle configuration
角式 Angie type
角式節流閥 Angle Throttle Valves
角式截止閥 Angle Stop valves
鉸鏈閥；片狀閥 flapper valve
節流閥 throttle valve
節流閥 choke valve
節流閥；節流 throttle
結構長度 Face-to-face dimension ;End-to-end dimension; Face-to-centre dimension
結構形式 Type of construction
截止閥 Globe valve
截止閥 Shut-off Valve
截止閥；關斷閥 shut-off valve
截止式隔膜閥 Globe diaphragm valve
緊急切斷閥 Emergeny Cut-off Valves
進氣閥 air intake valve
進水閥；進口閥門 inlet valve
靜態特性 Static characteristics
靜態特性偏差 Static characteristics derivation
開閥過冷度 Subcooled temperature of open valve
開閥溫度 Opening valve temperature
開啟高度 Lift
殼體試驗 Shell test
殼體試驗壓力 Seal test pressure
空氣閥門 Air valves
快速排污閥 Quick Draining Valves
類型 Type
冷凝結水排量 Cold condensate capacity
冷態試驗差壓力 Cold differential test pressure
理論排量 Theoretical flowing capacity
連接槽尺寸 Dimension of connecting channel
連接尺寸 Conncetion cimension
連接形式 Type of connection
簾面積 Curtain area
流道面積 Flow area
流道直徑 Flow diameter
流量孔板 flow orifice plate
流量控制閥 flow control valve
流量特性 Flow characteristics
流量特性偏差 Flow characteristics derivation
漏汽量 Steam loss
脈沖式疏水閥 Impulse steam trap
密封面 Sealing face
密封試驗 Seal test
密封試驗壓力 Seal test pressure
明桿平行式雙閘板閘板 Double Disk Parallel Gate Valves
明桿閘閥 Outside screw stem rising through handwheel type gate valve
膜片 Diaphragm
內壓自封 Pressure seat
逆止閥；止回閥 check valve
逆止閥；止回閥 non-return valve
逆止閥;止回閥;單向閥 check valve
排放背壓力 Brilt-up back pressure
排放壓力 Relieving pressure
排灰閥 Ash valves
排量系數 Coefficient of discharge
排氣閥 air release valve
排氣閥 Exhaust valves
排氣閥 Vent Valve
排水閥 Drainage valves
排水溫度 Temperature at discharging condensate
排污閥 blowdown valve
排污箱(閥) Waste Valves
排渣閘閥 Scum Gate Valves
盤閥 moushroom valve
盤狀閥 plate valve
旁路閥 by pass valve
配汽活塞閥缸套 piston valve line
噴射閥 injection valve
噴射閥 sprayer valve
噴水閥 spray water valve
頻跳 Chatter
平衡閥 Balance valves
平衡式 Balance type
平行式閘閥 Parallel gate valve Parallel slide valve
啟閉件 Disc
啟閉壓差 Blowdown of a safety valve
起始升程 Commencement of lift
氣動裝置 Pneumatic actuator
氣閥搖臂 valve arm
氣－液動裝置 Pneumatic-hydraulic actuator
潛水電泵(排污泵) Submerged Motor Pumps
切斷閥;截止閥 block valve;shut-off valve;stop valve
切斷式止回閥 stop check valve
切換閥;多向閥 changeover valve
球、球芯 Ball
球閥 Ball valve
球閥 globe valve
球體 Ball
全啟式安全閥 Fall lift safety valve
熱凝結水排量 Hot condensate capacity
入口隔離門 suction isolating valve
塞子 Plug
三通閥 three-way isolating valve
三通閥 three-way valve
三通式 Three way type
上密封 Back seat
上密封試驗 Back seal test
滲漏量 Leckage
升降立式止回閥 Vertical lift check valve
升降式止回閥 Lift check valve
適用介質 Suitable medium
適用溫度 Suitable temperature
手搖油泵(閥) Manual Oil Pumps Valves
疏水閥 drain valve
雙金屬片式疏水閥 Bimetal elements steam trap
雙口排氣球 Double Opening Exhaust Valves
雙聯彈簧式安全閥 Duplex safety valve
雙閘板 Double gate disc
雙閘板平板閘閥 Double Disc Flat Gate Valves
水封閘閥 Water Seal Gate Valves
水力噴射器(真空泵) Vacuum Pumps
伺服閥 servovalve
填料 Packing
填料墊 Packing seat
填料函 Stuffing
填料式旋塞閥 Gland packing plug valve
填料箱 Stuffing box
填料壓蓋 Gland
通氣閥 breather valve
通氣閥；呼吸器 breather
通用閥門 General valve
吐出閥；排出閥 discharge valve
吐出閥限位器 delivery valve guard
微啟式安全閥 Low lift safety valve
微阻緩閉止回閥 Tiny Drag Slow Shut Check Valves
吻合度 Percent of contact area
蝸輪傳動蝶閥 Butterfly Valves with Gear Actuator
蝸輪傳動裝置 Wormgear actuator
屋脊式隔膜閥 Weir diaphragm valve
無閥泵 valveless pump
無閥隔膜泵 valveless diaphragm pump
無閥振動泵 valveless vibration pump
無負荷漏汽量 No-load steam loss
無負荷漏汽率 Rate of no-load steam loss
吸（抽）氣閥 Aspirating valves
吸入閥 suction valve
吸入閥限位器 suction valve guard
先導式安全閥 Pilot operated safety valve
先導式液壓閥 Pilot-operated recing valve
相對靜偏差 Relative static characteristics derivation
相對流量特性偏差 Relative flow characteristics derivation
相對壓力特性偏差 Relative pressure characteristics derivation
銷軸 Hinge pin
楔式閘閥 Wedge gate valve
斜板式蝶閥 Indined disc butterfly valve
泄料（放空，排污）閥 Blowdown valves
泄壓閥 Decompression valves
泄壓閥 pressure release valve
泄壓閥；安全閥 relief valve
卸荷式減壓閥 Balanced recing valve
型號 Type Model
旋啟多瓣式止回閥 Multi-disc swing foot valve
旋啟式止回閥 Swing check valve
旋啟雙瓣式底閥 Double disc swing foot valve
旋塞閥 Cock
旋塞閥 plug valve
壓力（増壓）閥 Pressure valve
壓力調節閥；壓力控制閥 pressure controlled valve
壓力特性 Pressure characteristics
壓力特性偏差 Pressure characteristics derivation
壓力增長系數 Pressure increasing ratio
搖桿 Arm
液動裝置 Hydraulic actuator
液化氣管件 LPG Pipe Fitting
液下泵 Under Water Pumps
液壓執行器 hydraulic actuator
儀表針形截止閥 Meter Needle Type Globe Valves
溢流閥 overflow valve
翼形閥；錐形閥 wing valve
油封式旋塞閥 Lubricated plug valve
有閥翼板 double acting wing
有閥翼板 wing with valve
有負荷漏汽量 Load steam loss
有負荷漏汽率 Rate of load steam loss
圓板閥；圓盤閥 disc valve
圓盤式疏水閥 Shemostatic team trap
圓柱齒輪傳動裝置 Cylindrical gear actuator
圓錐齒輪傳動裝置 Conical gear actuator
閘板 Wedge disc
閘板式隔膜閥 Wedge diaphragm valve
閘閥 gate valve
閘閥 sluice valve
針形閥 Pintle valve ; Needle valve
真空破壞閥 vacuum breaker valve
蒸汽疏水閥 Automatic steam trap Trap
整定壓力 Set pressure
正向作用式減壓閥 Direct acting recing valve
支架 Yoke
直接載荷式安全閥 Direct loaded safety valve
直接作用式減壓閥 Direct-acting recing valve
直流式 Y-globe type
直流式截止閥 Oblique Stop Valve
直通單向閥 inline check valve
直通單向閥 straightway check valve
直通閥 Throughway Valve
止回閥 Check Valve
止回閥；迴流閥 reflux valve
制動閥 Brake valves
中壓閥門 Middle pressure valve
鍾形浮子式疏水閥 Inverted bucket steam trap
鍾形罩 Inverted bucket
軸套 Axis Guide
主閥 Main valve
主要外形尺寸 Prime out-form dimensions
主要性能參數 Specifeca tion speeification
注液漏斗閥 Priming Tundish Valve
柱塞閥 Plunger valve
柱塞截止閥 Plunger Globe Valve
柱塞型擺動閥 rocking plunger valve
撞擊手輪 Impact handwheel
錐形閥；翼形閥 conical valve
自動循環閥 Automatic Recirculation Valve
組合閥 Combination valves
最大過冷度 Maximum subcoold temperature
最大流量 Maximum flow rate
最大壓差 Maximum differential pressure
最低工作壓力 Minimum operating pressure
最高背壓率 Maximum rate of back pressure
最高工作背壓 Maximum operating back pressure
最高工作溫度 Maximum operating temperature
最高工作壓力 Maximum operating pressure
最高排水溫度 Maximum temperature at discharging
最高允許溫度 Maximum allwable temperature
最高允許壓力 Maximum allowable pressure
最小過冷度 Minimum subcooled temperature
最小壓差 Minimum differntial pressure

3. 閥門的字母簡寫

安全閥A

蝶閥D

隔膜閥G

止回閥(底閥)H

截止閥J

節流閥L

排污閥P

球閥Q

疏水閥S

柱塞閥U

旋塞閥X

減壓閥Y

閘閥Z

閥門可用於控制空氣、水、蒸汽、各種腐蝕性介質、泥漿、油品、液態金屬和放射性介質等各種類型流體的流動。閥門根據材質還分為鑄鐵閥門，鑄鋼閥門，不銹鋼閥門，鉻鉬鋼閥門，鉻鉬釩鋼閥門，雙相鋼閥門，塑料閥門，非標訂制閥門等。

(3)氣閥門英文擴展閱讀

閥門日常保養

1、閥門存放環境需注意，應存放在乾燥通風的室內，且堵塞通路兩端。

2、閥門應定期檢查，並清除其上的污物，塗抹塗防銹油在其表面。

3、安裝應用後的閥門，應對其進行定期檢修，以確保其正常工作。

4、應查看閥門密封面是否磨損，並根據情況進行維修或更換。

5、檢查閥桿和閥桿螺母的梯形螺紋磨損情況、填料是否過時失效等，並進行必要的更換。

6、應對閥門的密封性能進行試驗，確保其性能。

7、運行中的閥門應完好，法蘭和支架上的螺栓齊全，螺紋無損，沒有松動現象。

8、如手輪丟失，應及時配齊，而不能夠用活扳手代替。

9、填料壓蓋不允許歪斜或無預緊間隙。

10、如果閥門使用環境較為惡劣，易受雨雪、灰塵、風沙等污物沾染，則應該為閥桿安裝保護罩。

11、閥門上的標尺應保持完整、准確、清晰，閥門的鉛封、蓋帽。

12、保溫夾套應無凹陷、裂紋。

13、運行中的閥門，避免對其敲打，或者支撐重物等。

4. 閥門rov，bv之類的英文縮寫，有沒有人系統的給我一份呢

ACV automatic control valve 自動控制閥
AIV air inlet valve 進氣閥
AOIV automatically operated inlet valve 自動操作進給閥
AOPV Air-Operated Plastic Valve 氣動塑料閥
a/or automatic operated valve 自動操作閥
AV angle valve 角閥
AWV automatic washing valve 自動洗滌閥
BAV ball valve 球閥
BB bolted bonnet 螺栓連接閥蓋
BC bolted cap 螺栓連接閥帽
BCV ball check valve 球止回閥
BDV blow down valve 放泄閥
BFV butterfly valve 蝶閥
BUV butterfly valve 蝶閥
BV breather valve 呼吸閥
BVMA British Valve Manufactures Association 英國閥門製造商協會
BWV back water valve 回水閥
CEIR [法] Comité Européen de l'Instrie de la Robineterie 歐洲閥門製造業委員會
CHV check valve 止回閥
CV check valve 止回閥
DBB double block and bleed 雙截斷排放（閥）
EB extended bonnet 閥蓋加長頸
EPV elector-pneumatic valve 電動-氣動閥
ESV emergency shut valve 緊急切斷閥
EXHV exhaust valve 排氣閥
FTV foot valve 底閥
FV flush valve 沖洗閥
GSV gas sampline valve 氣體采樣閥
GSV globe stop valve 球形截止閥
GTV gate valve 閘閥
GV gate valve 閘閥
HCV hose connection valve 軟管連接閥
HCV hydraulic control valve 液壓控制閥
HFSV high flow shutoff valve 高速關閉閥
HPV high pressure valve 高壓閥
ILRV in-line relief valve 管道泄壓閥
INO inlet open 進氣閥打開
INV in-line needle valve 管道針形閥
IS inside screw stem 內螺紋閥桿（暗桿）
IV inlet valve 進氣閥
JCVA Japan Cylinder Valve Association 日本高壓容器及閥門協會
MGV electromagnetic valve 電磁閥
MSS Manufacture's Standardization Society of Valve and Fittings Instry （美）閥門與管件工業製造商標准化協會
NRV non-return valve 止回閥
OHV overhead valve 頂閥
PCV pressure control valve 壓力調節閥
PRV pressure recing valve 減壓閥
PSB perssure seal bonnet 內壓自密封閥蓋
QEV quick exhaust valve 快速排氣閥
RV pressure recing valve 減壓閥
ROV Roll-Over Valve 旋轉閥

SOAV solenoid operated air valve 電磁操縱氣閥
SOV shut-off valve 斷流閥
SSV surface safety valve 地表（井口）安全閥
ST steam trap 蒸汽疏水閥
SV safety valve 安全閥
TDCV turning disc check valve 翻轉閥瓣止回閥
TV throttle valve 節流閥
TVV thermal vacuum valve 溫控真空作用閥
TWV Tee valve 三通閥
USV underwater safety valve 水下安全閥
val. valve 閥門
VB valve body 閥體
VB valve box 閥箱
vl. valve 閥門
VSLO valve stem leak-off 閥桿漏泄
YV wye valve Y形閥，斜桿直流式閥

5. 閥門英文翻譯

ATM不是自動提款機嗎
RESP 應該是respiration的縮寫

6. 哪位大哥有特氣氣櫃中各閥門的英文縮寫代表的意思謝謝！

你好，我就來是從事這方面自的工作的。sv是手動閥，av是氣動閥，reg是調壓閥，efs是過流遮斷器， pt是數字顯示器（功能就和壓力表一樣） vg是真空發生器，cv是逆止閥。。。。。。 （LPT，HPT ，HPG，LPG）這四個是差不多的只不過是數顯壓力計和指針式壓力表，GNBV動源氮氣手閥，PNBV低壓氮氣手閥 VPT是測量vent的數顯壓力計，還有很多，有什麼需要幫忙的盡管說！呵呵，分給我拉。---河北廊坊 又給你補充了

7. 閥門專業術語英語系列

Shanghai valve Manufacturing Co., Ltd.

泵閥是泵和閥門的統稱。 非用於泵的閥門或具有泵作用的閥門。泵和閥常常聯系內在一起的原因容是使用場合。就是說有泵的地方一般都有閥門，有閥門的地方往往需要泵。他們都用於液體輸送的地方。當然，閥門還用於氣體。真空泵也與氣體有關。
另一個聯系就是有相當多製造商們既生產泵又生產閥門，其製造材料等也十分相近。
所以一般英文只寫閥門。

名片上寫的valve pump或者pump valve是為了讓人更加了解公司不只做閥還做泵

如果你一定要加的閥可以寫成
Shanghai valve&pump Manufacturing Co., Ltd.
寫前寫後都不影響

8. 閥門翻譯成英文

搞笑 看誰幫你

9. 各類閥門的英語名稱及相關詞彙

閥門相關英語詞彙
air-compressor valve 空氣壓縮機閥門
automatic cutout valve 自動切斷閥門
backlash valve 無游隙閥門
High temperature valve 高溫閥門
hose valve 水帶閥門
pipe manifold valves 管道匯集器閥門
pneumatic cylinder cock valve 風動汽缸排水閥閥門
pneumatic positioner valve 氣動閥門定位器
pneumatic sander valve 風動撒砂器閥門
quick opening valve 快開閥門
quick-opening gate valve 速啟閥門
standby valve 應急閥門; 備用閥門
two selenoid 雙螺管閥門
valve chest 閥門室
valve clearance 閥門間隙； 閥余隙
valveman 閥門操作者
wash-out valve 清洗閥門
adjusting valve 調整閥, 調節閥
admission valve 進氣閥; 進漿閥
air admission valve 進氣閥
air bleed(ing) valve 排氣閥; 排氣嘴
air control valve 空調閥
air cylinder valve 氣筒閥
air escape valve 泄氣閥
air inlet valve (=air intake valve) 進氣閥; 進風閥
air operated throttle motor 風動節流器, 風動節流閥馬達
air pilot valve 空氣導向閥
air pressure governor valve 風壓調壓閥
air relay valve 空氣中繼閥
air release valve (=air relief valve) 排氣閥; 放空閥
air reversing valve 空氣換向閥
air shut-off valve 空氣關閉閥
air signal recing valve 空氣信號減壓閥
air slide valve 空氣分配閥
air starting (control) valve 空氣起動(控制)閥
air straining check valve 空氣濾塵止回閥
air valve 空氣閥
air vent valve 氣動調壓閥, 排氣閥
air-actuated direction valve 氣動控制換向閥
air-compressor valve 空氣壓縮機閥門
air-operated valve 氣動換向閥
air-vacuum proportional valve 空真比例閥
air-vacuum two way valve 空真二位閥
alarm valve 報警閥
aligned grid valve 柵極中點校直的電子管閥
Allan valve 阿倫滑閥
altitude valve 【航空】高度閥(航空發動機汽化器的可調整閥)
ammonia valve 【工】氨閥
angle back-pressure valve 背壓角閥
angle globe valve 折角球形閥
angle stop valve 彎形止閥, 折角止閥
angle valve 角閥
angle water valve 折角水閥
annular ring valve 環形閥; 環狀閥
anti-g valve 【航空】防超重活門, 抗重力閥
application pilot valve 作用導閥
application valve 作用閥, 控制閥
ashpan blower valve 灰盤吹風閥
Askania valve 射流管閥
atmos valve (=atmospheric valve) 大氣閥, 空氣閥; 放空閥
autocontrol valve 自動控制閥
automatic air valve 自動空氣閥
automatic brake valve 自動制動閥
automatic control valve 自動控制閥
automatic cutout valve 自動切斷閥門
automatic delivery control valve 自動輸送控制閥
automatic drain valve 自動排水閥
automatic expansion valve (定壓式)自動膨脹閥
automatic gas sampling valve 自動氣體進樣閥
automatic recing valve 自動減壓閥(高速制動機)
automatic regulating valve 自動調節閥
automatic spring loaded valve 自動彈簧閥

詳細的可以看這里了，很多的：）~~
http://www.cihui.biz/word/15/2006_03/%B7%A7%C3%C5%CF%E0%B9%D8%D3%A2%D3%EF%B4%CA%BB%E32350_1.html

閥門相關 / 閥門技術 / 對照英語詞彙
http://famen.52angell.com/famen/1/2/2006_01/1_1.html

10. 閥門英語翻譯

閥門的設計是來需要水的流自向消防噴水滅火系統的控制，並應在特殊系統的水控制閥類上市1（VLFT）。中期審查和提供的主體，鑄造和Hytrotest和座椅泄漏測試報告0.3第三方認證的CER要求; ABS的，勞埃德或挪威船級社;
先導控制應prepiped和測試之前裝運;管道電磁閥的名字必4倍建設最低和1類第2分部合適，D組區域電磁閥線圈應為24伏直流電，上游水連接先導控制應當與蒙乃爾過濾器。 ;提供手動閥門管道輸送到當地的主要開放汽車運行中常見流失;主閥是由水pressure.Pilot系統控制手段（345千帕，克儀表風）在一個封閉的地位將與24V的驅動電壓來發泄的電磁閥線圈或排放來自買家的外部345千帕，克（50PSIG）空氣供應本地熔線火焰檢測裝置
火焰檢測裝置。液壓先導閥排氣解除
帽子/隔膜壓力打開雨淋閥
就地手動復位試點模式CMDL;常開裝飾帶復位handle.Pilot駕駛員應排出洪水比控制膜片氣開大洪水時，主迴路按ext.fire減少到137psi -克（20psig）復位處理時-> 205kpa。。克（30 psig）的或更大的